Yamaha's RX-V1800 yielded the fine technical performance usual from the firm's A/V receivers. Power exceeded its specs by a good margin and bettered 100 watts all around, even with 5 channels driven. The unit's power supply appeared to run out of current when 2 more channels were added, however, since the 7-channel result dropped by nearly 3 dB, to 55 watts—a non-issue in the real world., where program signals never demand this level of stability. Yamaha equips its receiver with a software setup switch for speakers of 6-ohms or lower, which effectively limits power to about two thirds.
Frequency response, distortion, and D/A linearity were uniformly excellent, and crossover responses were all bang on the numbers, with nicely accurate slopes—not always the case. PCM and Dolby Digital noise were very good, if a dB or 2 shy of the best we've seen, although S/N on the analog-multichannel inputs was truly superior. I note that the analog input was a good bit more sensitive than the digital ones (re: our reference levels of -20 dBFS or 200 mV for 1 watt output), so listeners who switch from the latter to the former without adjusting the volume could be in for a roughly 10 dB surprise. While this sounds like a lot, most characterize it as only about subjectively "twice as loud" or so.
All data were obtained from various test DVDs using 16-bit dithered test signals, which set limits on measured distorting and noise performance. Reference input level is –20 dBFS, and reference output is 1 watt into 8 ohms. Volume setting for reference level was -6. All level trims at zero, except for subwoofer-related tests, all speakers were set to "large," subwoofer on. All are worst-case figures where applicable.
Output at clipping (1 kHz into 8/4 ohms)
1 channel driven: 158/281 W (22/24.5 dBW)*
5 channels driven (8 ohms): 103 W (20.1 dBW)
7 channels driven (8 ohms): 55 W (17.4 dBW)
Distortion at 1 watt (THD+N, 1 kHz)
8/4 ohms: 0.02/0.03%
Noise level (A-wtd): –73.4 dB
Excess noise (with sine tone)
16-bit (EN16): 0.9 dB
Frequency response: 20 Hz to 20 kHz +0, –0.2 dB
Reference input and output level is 200 mV; volume setting for reference output level was -14.
Distortion (THD+N, 1 kHz, 8 ohms): 0.008%
Noise level (A-wtd.): –90.1
Frequency response: <10 Hz to 166 kHz +0, –3 dB
Reference level is –20 dBFS; all level trims at zero. Volume setting for reference level was -3.
Output at clipping (1 kHz, 8/4 ohms, both channels driven): 150/237 W (21.8/23.7 dBW)*
Distortion at reference level: 0.02%
Linearity error (at –90 dBFS): 0.2 dB
Noise level (A-wtd): –74.8 dB
with 96-kHz/24-bit signals: –85.4 dB
Excess noise (with/without sine tone)
16-bit (EN16): 0.6/0.8 dB
quasi-20-bit (EN20): 13.3/12.1 dB
Noise modulation: 0.6 dB
Frequency response: <10 Hz to 20 kHz +0, –0.3 dB
with 96-kHz/24-bit signals: <10 Hz to 44 kHz +0, –3 dB
*With receiver's software setup switch at 8 ohms. With switch at 6 ohms, power was limited to about 90 and 160 watts (19.5/22 dBW) into 8 ohms and 4 ohms respectively.
Measured results obtained with Dolby Digital test signals.
Subwoofer-output frequency response (crossover set to 80 Hz): 24 dB/octave (approx.) above –6-dB rolloff point of 80 Hz
High-pass-filter frequency response (crossover set to 80 Hz): 12 dB/octave below –3-dB rolloff point of 80 Hz
Maximum unclipped subwoofer output (trim at 0): 6.8v
Subwoofer distortion (from 6-channel, 30-Hz, 0-dBFS signal; subwoofer trim set to 0): 0.3%
Crossover consistency: bass crossover frequency and slope were consistent for all sources and formats
Signal-format consistency: consistent for all applicable formats
Speaker size selection: all channels can be set to "small"
Speaker-distance compensation: available for all main channels.
Full Review
Test Reports RSS Feed
More Test Reports
Back to Homepage
What's New on S&V